Tel: +86-532-83500538
News
Home > News > Content

Technique Of Using Steel Wire Clamp

Qingdao Jiechao Machinery Co.,Ltd | Updated: Sep 20, 2017



The Wire rope clamp is connected by the rope card sleeve and the top fastening bolt, and the rope card sleeve is formed by the precision casting, and the wire rope is divided and fixed and the end head is fixed in two ways. In use, the wire rope lap is fixed, the wire rope two end head is opposite through the rope card sleeve the steel wire rope hole, adjust the wire rope tightness, Wire rope clip use our specially developed tensioning tool to tighten the wire rope, and then tighten the top fastening bolt to tighten the wire rope, so as to play the role of tension binding reinforcement; Wire rope clip wire rope ends fixed, Wire Rope end head through the rope card sleeve of the wire hole back through the rope jacket, form a closed ring sleeve on the T-tie, adjust the tension of the wire rope, use our specially developed tensioning tool to tighten the steel wire rope, and then tighten the top tightening bolts to tighten the wire rope, Wire rope clip so as to play the role of tightening binding. Can replace the traditional wire rope clamp. It is applicable to the binding and strengthening of steel, machinery and wheeled equipment in railway transportation.

Method of using wire rope clamp

1. The clamp seat shall be fastened to the working section of the Wire rope, and the U-shaped bolt is fastened on the end of the wire rope, can avoid the long rope is not the rope card deformation (if the U-ring part of the rope card on the wire line side, it will be due to the U-ring and wire rope contact surface small, Wire rope clip so that the wire rope produced bending and sprain, affecting the tensile strength of the main rope).

2. The wire rope clamp shall not be arranged alternately on the wire rope.

3. The distance between the clips is equal to 6-7 times the diameter of the wire rope.

4. The minimum number of mm wire clips for the nominal size of rope clips

5, fastening the steel wire clamp must consider each clamp reasonable force, Wire rope clip from the ring to the farthest of the rope clamp should not be fastened first alone

6, the rope clip closest to the sleeve ring should be as close to the sleeve ring as possible. Wire rope clip The farthest one with the second between left a little roundabout, in order to facilitate the inspection.

7, the short edge of the wire rope should not be less than 150MM, and with thin wire winding up. The steel wire rope chuck should pay attention to the following points when using:

A) When selecting Chuck, it is necessary to make the inner net distance of U-ring larger than the diameter of wire rope 1~3mm, too big card buckle connection card is not tight, prone to accidents.

b When the top chuck must tighten the bolt until the rope is compressed $number diameter, Wire rope clip and after the rope force, and then the chuck bolts to tighten once, to ensure that the joint firmly and reliably. c) The Chuck is arranged in a smooth arrangement, and the U-shaped part is contacted with the line and cannot be contacted with the main rope, as shown in Figure A. If the U-shaped part is in contact with the main rope, Wire rope clip the main rope is compressed and the force is easily broken. D to make it easier to check the reliability of the joint and to find whether the wire rope is slipping, can be at the end of the clip head about 500mm after a chuck, and will line release a "Safe bend", so that when the wire rope of the joint is sliding, "safety bend" is first straightened, Wire rope clip then should take immediate measures to deal with.

2 a) When selecting Chuck, it is necessary to make the inner net distance of U-shaped ring larger than the diameter of wire rope 1~3mm, too big card buckle connection card is not tight, easy to happen accident.

b When the top chuck must tighten the bolt until the rope is compressed $number diameter, and after the rope force, and then the chuck bolts to tighten once, to ensure that the joint firmly and reliably. c) The Chuck is arranged in a smooth arrangement, and the U-shaped part is contacted with the line and cannot be contacted with the main rope, as shown in Figure A. If the U-shaped part is in contact with the main rope, Wire rope clip the main rope is compressed and the force is easily broken. D to make it easier to check the reliability of the joint and to find out if the wire rope is slipping, a chuck can be secured at about 500mm behind the last Chuck and a "safe Bend" will be released from the line. In this way, when the wire rope of the joint is sliding, the "safety bend" is first straightened and the action should be taken immediately.

By the way, the comparison of the current use of more than the wire rope head of the practice: when braided connection, the length should not be less than 15 times times the diameter of wire rope, and not less than 300mm. Wire rope clip The connection strength must not be less than 75% of the breaking tensile force of the wire rope;